The Mini-Kits High Performance VHF 2M RX/TX masthead Pre-amplifier has been designed to be easy to construct, and is suitable for the 144-148MHz Amateur Band. The design uses a Mini-Circuits PGA-103 E-PHEMT amplifier that has a very high dynamic range and ultra low noise figure, and provides superior performance to Mos or GaAs FETs. The design incorporates VOX RF sensed changeover Relays for Trasnsceivers up to 100 Watts CW without using sequencing, or can handle up to 500 Watts PEP if sequencing is used. An on board bias tee ( DC power injector ), allows the pre-amplifier to be antenna mounted and powered via the coaxial cable. A Tuned input T type filter and output low pass filter provides high rejection of signals at 50 and 430MHz.
THIS KIT IS NOT FOR BEGINNERS AND REQUIRES VERY EXPERIENCED SOLDERING SKILLS
The Product picture shows a completed EME220-2M-Rev1.3 KIT1 product with Optional BNC connectors.
This product is ideal for use with the
Icom Multimode UHF transceivers including the IC275, IC820 / 821, 910,
IC9100, and IC9700 that have a PREAMP switch to supply +12vdc out of the
antenna connector on RX mode. Transceivers without this function will
require an external bias tee like the Mini-Kits EME168-2-70 to supply DC power up the coaxial cable. Refer to the application block diagram and the
EME220 Kit Webpage for more information
Please Note: Built products usually need to be constructed and can take up to 2 weeks to ship depending on work load, but are normally shipped in few days.
EME220-2M KIT1 is a Basic Kit that includes the PC board, Instructions, and all on board components. No connectors or enclosure are included. Requires Complete construction.
EME220-2M KIT2 is the KIT1 but also includes the BNC connectors and Nickel sprayed GME enclosure. Requires Complete construction.
EME220-2M KIT3 is the KIT1 but also includes a Hammond 1590S enclosure, BNC connectors and all hardware. Requires Complete construction.
EME220-2M-MH Is a fully constructed product in a Nickel sprayed GME Masthead enclosure with female BNC connectors.
EME220-2M-MOD Is a fully constructed Module board with female BNC connectors.
EME220-2M-BNC-S Is a fully constructed product in a Hammond 1590S Die cast enclosure with female BNC connectors, 2.1mm DC socket.
The basic EME220-2M KIT1 Does Not include connectors, miscellaneous hardware, or enclosure. The KIT2 and KIT3 includes the enclosure, connectors, 2.1mm DC cable and all required hardware. These Kits are for experienced constructors that have had experience with SMD construction. The EME220-2M-KIT3 requires metalworking tools to drill the enclosure.
|Frequency Range: ||140 to 150MHz ( BW 10MHz @ 1dB ) |
|Band Rejection:||Typically 40dB @ 50MHz, 60dB @ 430MHz |
|Gain Adjustable:||Typically +18dB Max, 10dB Min @ 145MHz |
|Noise Figure: ||0.8dB ( Typically <0.7dB @ 145MHz ) |
|Through Loss: ||0.05dB @ 145MHz ( Bypass Mode ) |
|RF Power Handling: ||100W CW ( Un-Sequenced ) 500W PEP ( Sequenced ) |
|Minimum RF Input: ||+20dBm ( 100mW ) To activate the RF sensing circuit|
|Operating Voltage:||+11 to 15vdc ( +12vdc @ 150mA Recommended )|
|Board Size:||80mm L x 84mm W x 25mm H ( with BNC connectors ) |
|Kit Webpage:||For actual product Tests see the EME220 Kit Webpage|
For more information please see the EME220 KIT WEBPAGE
2m 144MHz VHF RX/TX Preamplifier
- Brand: Mini-Kits
- Product Code: EME220-2M KIT
- Quantity In Stock: 10
- Export: $54.50