EME5800 SERIES KITS

Please Note: that all information including pictures on this web page are copyright to Mini-Kits and must not be used on any other web site, or reproduced in any publication.

Description:

The EME171B Universal Microwave PC board was designed as a low cost way of experimenting on the microwave bands, and allows various building blocks like Transverters, multipliers, and RF amplifiers to be constructed.

A complete Transverter for 5800MHz can be easily constructed using a number of Kits and components available from Mini-Kits. The picture below shows a prototype chassis with a fully working transverter for 5800MHz. Pipe cap cavity filters are used to effectively filter out image and local oscillator frequencies, allowing IF frequencies down to 144MHz to be used.

The use of Cavity filters using pipe-caps have been used by Hams for many years, and make excellent filters that can be easily adjusted in frequency and bandwidth. They also allow relatively narrow filters to be constructed which more effectively filter harmonics and oscillator noise, allowing low Transverter I/F frequencies to be used. Cavity filters also improve the stability of the design making it easier to mount into a smaller enclosure, compared to printed strip line filters that can radiate RF.

Most of the EME5800 series Kits require at least +10vdc, so that they can easily be used for portable battery operation. Only the EME5.8G-AMP1 Kit has the requirement of +12 volts for it's high 1dB compression Gali-84 amplifier, to produce a clean signal from the transmitter.

The EME5.8G series Kits use modern low noise high gain amplifiers, including the Mini-Circuits Gali, and Avago MGA series, which makes it very easy to now construct a high performance Transverter with fewer devices. A low noise MGA-86563 GaAs MMIC is used for the Transverter receive amplifier, guaranteeing performance and requiring no input matching.

Kit Constructors Alert:

1/ There are no current alerts for these Kits.

EME5.8G-CV7 Kit Notes:

The EME5.8G-CV7 Kit is a simple Up / Down Converter that can be used as the basis to construct a complete Transverter, or Receiver only converter that can be tuned for use between 4000 and 7500MHz. The mixer, filter, and diplexer circuitry is bi-directional and allows the board to be used as a receive downconverter, and transmit up converter to produce a -16dBm output @ 5.8GHz. The pipecap filter is narrow enough to allow an IF frequency as low as 144MHz to be used. The converter board can be used to construct a complete 5.8GHz Transverter as shown in the Block Diagram, and shows which Kit products are required and typical gain and power levels. BUY THIS PRODUCT

EME5.8G-CV17 Component View
This Image shows the component side of a early prototype EME5.8G-CV17 Frequency Converter Kit
EME5.8G-CV17 Top View
This Image shows how the pipecap and the QF0.086 coaxial cable is fitted to an early prototype board. Later EME171B boards have a voltage regulator on the board.

EME5.8G L/O MULTIPLIER:

A range of local oscillator multiplier and amplifier filter Kits are available for either construction of multipliers for transverter local oscillators, Beacons, or ATV transmitters. The 5800MHz Multiplier Block Diagram shows which Kits products are required and typical gain and power levels.

  • EME5.8G-MLT KIT1 5800MHz Multiplier Kit ( only has 0dBm output so requires an amplifier. )
  • EME5.8G-AMP KIT1 5800MHz Filter Amplifier Kit ( Used with the EME5.8G-MLT KIT1 for extra L/O filtering and to amplfy the output to +10dBm. )
EME5.8G-MLT Component View
The Image shows the component side of a completed EME5.8G-MLT board
EME5.8G-FLT Top View
The Image shows the groundplane side of the board and how the pipecap and +9v regulator is fitted.
EME5.8G-AMP1 Output
The Image shows the output from the EME5.8G-AMP1 Amplifier Filter board that is used after the multiplier board to further filter amd amplifier the local oscillator to around +10dBm output at 5616MHz.
EME5.8G-MLT Output
The Image shows the output from the additional EME5.8G-FLT Filter board which cleans up the output producing a clean 3256MHz signal.
EME5.8G-FLT Filter
The Image shows the frequency response of the filter on the EME5.8G-FLT board. The filter is the same on the EME5.8G-MLT board and with both boards gives good LO rejection at 3456MHz.

EME5.8G AMPLIFIER:

The EME5.8G-AMP2 Driver Kit has been designed to be used in conjunction with the EME5.8G-TRV Kit to produce around +13dBm output on TX. The Kit can also be used as a general purpose filter amplifier with +32dB gain, and a +20dBm @ 1dB compression output. BUY THIS PRODUCT

EME5.8G-AMP2 Component View
The Image shows the component side of a completed EME5.8G-AMP2 Driver Amplifier board
EME5.8G-AMP Top View
The Image shows the groundplane side of the board and how the pipecap and +9v regulator is fitted.
EME5.8G-AMP1 Filter
The Image shows the Frequency response and S21 gain from the EME5.8G-AMP1 Driver Amplifier board.
EME5.8G-AMP1 Output
The Image shows the RF output from the EME5.8G-AMP1 Driver Amplifier board. Further filtering would be recommended to reduce the unwanted outputs.

What Other Components Are Required:

A number of other Kits and Components are required to construct a complete transverter. For a 144MHz IF, a 104MHz crystal is used with the EME175 Kit1 oscillator Kit to produce a 624MHz output and then multiplied x9 to 5616MHz using the EME5.8G-MLT Multiplier Kit. For a 432MHz IF, a 98.666666MHz crystal is used with the EME175 Kit1 oscillator Kit to produce a 592MHz output and then multiplied x9 to 5328MHz using the EME5.8G-MLT Multiplier Kit. The EME177 Heater Kit is high recommended when used with the 60 degree C Crystals from Mini-Kits For more information on the EME175 oscillator, and EME177 Heater Kits please see the EME175 Kit web page.

For sequencing and switching of the RF and power supply voltages the EME166 Sequencer Kit is highly recommended. The EME166 can easily handle the single I/F connection on the EME5.8G-TRV transverter.

Currently there is no Antenna Relay Kit available.

Currently there is no RF Power Amplifier Kit available for 5800MHz.

Cable and connectors can be found on the website. The SMA PCB mount connectors used on the EME5800 series Kits are part number SMA45 to suit a 1mm thick board.

A complete list of parts can be down loaded as a Excel spread sheet. DOWNLOAD

Kit Changes and Repairs:

EME5.8G-CV7

1/ The EME5.8G-TRV was changed by name to know be the EME5.8G-CV7 Kit.

EME5.8G-MLT-1

1/ There are no current changes to this Kit.

EME5.8G-AMP-1

1/ There are no current changes to this Kit.